Inc zloader 1.3.4 spi-nand:init ok. bbt ok. read uboot ok. start uboot... U-Boot 2011.09 (Mar 09 2022 - 17:06:52) for ZXIC U-Boot code: 0x21DF0000 -> 0x21E28EE0 BSS: -> 0x21EEB050 CPU: ZX297520V3 Board: ZX297520V3 monitor len: 0x00200000 ramsize: 0x02000000 TLB table at: 0x21ff0000 Top of RAM usable for U-Boot at: 0x21ff0000 Reserving 2048k for U-Boot at: 0x21df0000 Reserving 16k for nand dma buffer at: 0x21dec000 Reserving 2080k for malloc() at: 0x21be4000 Reserving 24 Bytes for Board Info at: 0x21be3fe8 Reserving 120 Bytes for Global Data at: 0x21be3f70 New Stack Pointer is: 0x21be3f60 RAM Configuration: Bank #0: 0x20000800 32 MiB relocation Offset is: 0x00000000 dram_bank_mmu_setup: bank: 0 monitor flash len: 0x00038EE0 Now running in RAM - U-Boot at: 0x21DF0000 Using default environment Destroy Hash Table: 21e29390 table = (null) Create Hash Table: N=91 DELETE CANDIDATE: "bootargs" hdelete: DELETE key "bootargs" DELETE ERROR ############################## INSERT: free(data = 21be8008) INSERT: done In: serial Out: serial Err: serial [sys_entry]<762>sys_entry ... [uboot_init_func]<702>go into uboot init func [uboot_init_func]<715>uboot init pull on pshold success [sys_entry_wdt]: watchdog no reset! [uboot_init_func]<715>uboot init wdt_reboot success [uboot_init_func]<715>uboot init dma success [uboot_init_func]<715>uboot init i2c success [zx234290_get_boot_reason_prev][START_UP_STATUS = 0x4] ... [zx234290_get_boot_reason_prev][USER_RESERVED = 0x0] ... [uboot_init_func]<715>uboot init peri success spi-nand: [SPI-NAND]: maf_id = 0xa1 [SPI-NAND]: dev_id = 0xa5 [SPI-NAND]: dev_id = 0x7f [SPI-NAND][A0] = 0x0 [SPI-NAND][B0] = 0x10 Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 nand_read_bbt: Bad block at 0x000005520000 [nand_init]<172>128 MiB. [uboot_init_func]<715>uboot init nand success [uboot_init_func]<715>uboot init partition success [uboot_init_func]<715>uboot init gmac success [uboot_init_func]<715>uboot init test success [efuse_get_data]<157>secure_flag=0xf8630900. [efuse_get_data]<176>secure_flag!=0xFF, SecureVerify->Disable. [uboot_init_func]<715>uboot init efuse success [prj_lcd_get_info]<829>LEAD_ST7735_128x128_F231E init: lcd man_id = 0x7c, dev_id=0x89f0 Scanning JFFS2 FS: . done. [uboot_init_func]<715>uboot init lcd success Scanning JFFS2 FS: . done. ucBootReason1st=0x54, ucBootReason2nd=0x0, battery_detect_flag=0x1 [uboot_init_func]<715>uboot init nvrw_flag success [boot_reason_init]<407>VALUE = 0x1f5b506e! [get_fota_update_flag]<837>fota_upflag=0 [boot_reason_init]<467>poweron_type=0x0. [uboot_init_func]<715>uboot init boot_reason success [uboot_init_func]<715>uboot init wdt success [uboot_init_func]<715>uboot init bat_det success [uboot_init_func]<715>uboot init boot_prepare success [boot_entry]<630>Normal entry! M0 image load success! [fs_load_zsp_image]<622>zsp image load begin... [fs_load_zsp_image]<628>zsp image load finished. [fs_load_arm_image_linux]<675>Load AP image, Size=0x419364, to 0x20447fc0. [fs_load_arm_image_linux]<679>AP image CRC Checksum=0x735c96f5. [fs_load_arm_image_linux]<681>AP image uiLoadPoint=0x20447fc0. [fs_load_arm_image_linux]<688>AP image load image finished [fs_load_arm_image_linux]<704>AP image Skip Secure Verify... [arm_image_crc_calc]<147>(cpuap)CRC Calculate start [arm_image_crc_calc]<150>(cpuap) CRC Calculate Res=0x735c96f5, Size=4297572 Bytes [arm_image_crc_calc]<156>(cpuap) CRC Check PASS! ### main_loop entered: bootdelay=0 ### main_loop: bootcmd=" bootm 0x20447fc0" ## Current stack ends at 0x21be3dc8 * kernel: cmdline image address = 0x20447fc0 show_boot_progress(1) ## Booting kernel from Legacy Image at 20447fc0 ... show_boot_progress(2) show_boot_progress(3) Image Name: Linux-3.4.110-rt140 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4297572 Bytes = 4.1 MiB Load Address: 20448000 Entry Point: 20448000 Verifying Checksum ... len = 419364,dcrc = 735c96f5,cal=735c96f5 OK show_boot_progress(4) show_boot_progress(5) show_boot_progress(6) kernel data at 0x20448000, len = 0x00419364 (4297572) show_boot_progress(14) ## No init Ramdisk ramdisk start = 0x00000000, ramdisk end = 0x00000000 @@@entry bootm_load_os uncompressing@@@ XIP Kernel Image ... OK OK kernel loaded at 0x20448000, end = 0x20861364 show_boot_progress(7) images.os.start = 0x20447FC0, images.os.end = 0x20861364 images.os.load = 0x20448000, load_end = 0x20861364 show_boot_progress(8) show_boot_progress(15) ## Transferring control to Linux (at address 20448000) ... ===chiid=0x1d63,boot_params=0x20440100 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.4.110-rt140 (SCM@ZTE) (gcc version 4.9.4 (Buildroot 2015.08.1-svn2614) ) #2 PREEMPT RT Fri Sep 8 16:23:35 CST 2023 [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=50c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: TSP ZX297520V3 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] softspinlock init success base=0xf83029c0! [ 0.000000] [CLK] zx29 tsp clk init ok. [ 0.000000] [PCU] PCU_INIT begin. [ 0.000000] [PCU] PCU_INIT end. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 7048 [ 0.000000] Kernel command line: root=/dev/mtdblock5 ro rootfstype=jffs2 console=ttyS1,921600 no_console_suspend mtdparts=spi-nand:128k@0x0(zloader),1m@0x20000(uboot),1m@0x120000(uboot-mirr),2m@0x220000(nvrofs),8m@0x420000(imagefs),22m@0xc20000(rootfs),8m@0x2220000(resource),83m@0x2a20000(userdata) lcd_id=124 battery_idt=1 boot_reason=0 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Memory: 27MB = 27MB total [ 0.000000] Memory: 23560k/23560k available, 4856k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc2000000 - 0xff000000 ( 976 MB) [ 0.000000] lowmem : 0xc0040000 - 0xc1c00000 ( 27 MB) [ 0.000000] modules : 0xbf000000 - 0xc0040000 ( 16 MB) [ 0.000000] .text : 0xc0048000 - 0xc03f06c8 (3746 kB) [ 0.000000] .init : 0xc03f1000 - 0xc0406000 ( 84 kB) [ 0.000000] .data : 0xc0406000 - 0xc0461340 ( 365 kB) [ 0.000000] .bss : 0xc0461364 - 0xc04a5808 ( 274 kB) [ 0.000000] NR_IRQS:150 [ 0.000000] [GIC]zx29 GIC initialized. [ 0.000000] ce_wclk=3250000, parent=main_clk_26m [ 0.000000] cs_wclk=32768, parent=main_clk_32k [ 0.000000] sched_clock: 31 bits at 32kHz, resolution 30517ns, wraps every 65535999ms [ 0.000000] cd_wclk=26000000, parent=main_clk_26m [ 0.000000] wt_wclk=32768, parent=main_clk_32k [ 0.000000] zx297520v system timer initialized [ 0.000000] console [ttyS1] enabled [ 0.000000] [UART]register_console: zx29 console registered! [ 0.026824] Calibrating delay loop... 1241.08 BogoMIPS (lpj=3102720) [ 0.054748] pid_max: default: 4096 minimum: 301 [ 0.054809] Mount-cache hash table entries: 512 [ 0.055267] CPU: Testing write buffer coherency: ok [ 0.055450] Setting up static identity map for 0x2070fe00 - 0x2070fe4c [ 0.062774] NET: Registered protocol family 16 [ 0.063842] kworker/u:0 used greatest stack depth: 2636 bytes left [ 0.065124] gpiochip_add: registered GPIOs 0 to 135 on device: zx29_gpio [ 0.065795] [GPIO]create sysfs interface [ 0.066284] [GPIO]zx29 GPIO initialized [ 0.167846] buck3v3 on, wifi power up. [ 0.169525] kworker/u:0 used greatest stack depth: 2484 bytes left [ 0.170654] spi_register_board_info success,devices_num=1 [ 0.171142] spi_register_board_info success,ret=0 [ 0.171752] wifi enable gpio success low85 [ 0.216857] bio: create slab at 0 [ 0.222564] [DMA]zx297520v2 DMA initialized [ 0.254669] zx29_i2c zx29_i2c.0: i2c-0: ZX29 I2C adapter [ 0.255737] zx29_i2c zx29_i2c.1: i2c-1: ZX29 I2C adapter [ 0.257965] NET: Registered protocol family 8 [ 0.258331] NET: Registered protocol family 20 [ 0.259643] cfg80211: Calling CRDA to update world regulatory domain [ 0.261108] Switching to clocksource zx29_ap_timer3 [ 0.263732] NET: Registered protocol family 2 [ 0.275878] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.277038] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.277770] TCP bind hash table entries: 256 (order: 0, 6144 bytes) [ 0.278533] TCP: Hash tables configured (established 1024 bind 256) [ 0.279296] TCP: reno registered [ 0.279937] NET: Registered protocol family 1 [ 0.281127] [xxx] softspinlock dev inited! [ 0.282989] jffs2: version 2.2. (NAND) (LZO) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.283874] msgmni has been set to 46 [ 0.286193] io scheduler noop registered [ 0.286499] io scheduler deadline registered (default) [ 0.287384] ##leadt15ds26_spi_init, line:1312[LCD][LEAD]spi_register_driver - leadt15ds26_spi. [ 0.290893] [zx29_uart_probe][2915]UART DMA is OPENED1 [ 0.291351] ttyS1 at MMIO 0x1408000 (irq = 33) is a zx29_UART [ 0.292510] TSP zx29 UART_1 probe OK [ 0.292907] TSP zx29 UART driver registered [ 0.295837] kworker/u:0 used greatest stack depth: 2468 bytes left [ 0.305419] brd: module loaded [ 0.312133] loop: module loaded [ 0.312561] logcat_printf init. [ 0.313018] cplog_init. [ 0.314361] Generic platform RAM MTD, (c) 2004 Simtec Electronics [ 0.315124] spi_nand_probe------------ [ 0.315826] [SPIFC]dma ok addr is 21904500 [ 0.316162] gpio,clk ,spifc en ok [ 0.316772] [SPIFC]request_irq ok [ 0.317047] spi-nand-dt spi-nand-dt: maf = a1,dev = a5, dev2 = 7f [ 0.317779] spi_nand wakelock ok [ 0.318206] [SPI-NAND]: maf_id = 0xa1 [ 0.318664] [SPI-NAND]: dev_id = 0xa5 [ 0.319122] [SPI-NAND]: maf_id = 0xa1 [ 0.319580] [SPI-NAND]: dev_id = 0xa5 [ 0.320068] [SPI-NAND]: maf_id = 0xa1 [ 0.320526] [SPI-NAND]: dev_id = 0xa5 [ 0.320983] NAND device: Manufacturer ID: 0xa1, Chip ID: 0xa5 (Paragon SPINAND 128MiB 1,8V 8-bit) [ 0.322113] 1 NAND maxchips chips detected [ 0.322631] [SPI-NAND][A0] = 0x0 [ 0.323028] [SPI-NAND][B0] = 0x10 [ 0.323669] Bad block table found at page 65472, version 0x01 [ 0.324554] Bad block table found at page 65408, version 0x01 [ 0.325286] nand_read_bbt: bad block at 0x000005520000 [ 0.325866] 8 cmdlinepart partitions found on MTD device spi-nand [ 0.326538] Creating 8 MTD partitions on "spi-nand": [ 0.327148] 0x000000000000-0x000000020000 : "zloader" [ 0.329284] 0x000000020000-0x000000120000 : "uboot" [ 0.331115] 0x000000120000-0x000000220000 : "uboot-mirr" [ 0.333190] 0x000000220000-0x000000420000 : "nvrofs" [ 0.335021] 0x000000420000-0x000000c20000 : "imagefs" [ 0.337188] 0x000000c20000-0x000002220000 : "rootfs" [ 0.339050] 0x000002220000-0x000002a20000 : "resource" [ 0.341125] 0x000002a20000-0x000007d20000 : "userdata" [ 0.343383] [ 0.343383] g_read_only_partition_table: [ 0.343902] offset=0x0, size=0x20000 [ 0.344360] offset=0x20000, size=0x100000 [ 0.346130] zx29_ssp zx29_ssp.0: setup for DMA on RX dma0chan5, TX dma0chan4 [ 0.347412] ##leadt15ds26fb_probe, line:1188[LCD][LEAD]leadt15ds26fb_probe in. [ 0.348205] ##leadt15ds26fb_init_gpio, line:496request lcd_reset failed [ 0.352020] PPP generic driver version 2.4.2 [ 0.352783] PPP BSD Compression module registered [ 0.353179] PPP Deflate Compression module registered [ 0.354553] PPP MPPE Compression module registered [ 0.354980] NET: Registered protocol family 24 [ 0.355560] [rtw_suspend_lock_init] ENTRY [ 0.356048] Realtek WLAN driver - version 1.7 (2020-02-07) [ 0.356750] Adaptivity function - version 9.1 [ 0.357269] wlan_index:0 1, 10,0x8179024c,0x0,0 [ 0.358062] ======== at_cdev_init [ 0.358306] ======== at_cdev_init 1 [ 0.358734] ======== at_cdev_setup_cdevCore Release: 3.20a [ 0.565460] Setting default values for core params [ 0.572296] Using Descriptor DMA mode [ 0.572570] Periodic Transfer Interrupt Enhancement - disabled [ 0.573303] Multiprocessor Interrupt Enhancement - disabled [ 0.574005] OTG VER PARAM: 0, OTG VER FLAG: 0 [ 0.574615] Dedicated Tx FIFOs mode [ 0.581268] #####diag_function_init@728:DIAG INIT [ 0.582489] #####acm_function_init@890:ACM INIT [ 0.584716] gadget: Mass Storage Function, version: 2009/09/11 [ 0.585296] gadget: Number of LUNs=2 [ 0.585754] lun0: LUN: removable read only CD-ROM file: (no medium) [ 0.586547] lun1: LUN: removable file: (no medium) [ 0.587219] gadget: android_usb ready [ 0.589538] input: zx29_keypad_int as /devices/virtual/input/input0 [ 0.591644] kpd request_irq irq_num=141. [ 0.601837] kpd request_irq irq_num=90. [ 0.611846] kpd request_irq irq_num=89. [ 0.618438] zx234290-rtc zx234290-rtc: rtc core: registered zx234290 as rtc0 [ 0.627624] i2c /dev entries driver [ 0.628753] charger probe. [ 1.627075] i2c_zx29: i2c transfer timeout [ 1.627441] zx234502-charger 1-0013: zx234502_hw_init err: -110 [ 1.628143] zx234502_probe Hardware init failed times = 1 [ 5.627197] zx29_i2c zx29_i2c.1: cannot get bus (error -110) [ 5.627746] zx234502-charger 1-0013: zx234502_hw_init err: -11 [ 5.628448] zx234502_probe Hardware init failed times = 2 [ 9.627197] zx29_i2c zx29_i2c.1: cannot get bus (error -110) [ 9.627716] zx234502-charger 1-0013: zx234502_hw_init err: -11 [ 9.628448] zx234502_probe Hardware init failed times = 3 [ 9.629119] zx234502_hw_init error!!! [ 9.629577] go to zx234500_prob!! [ 9.630249] eta4056_charger_probe start!! [ 9.942993] init usb in [ 10.053527] chg bat low will not inform usb [ 10.073913] chg gpio error ret = 0 [ 10.074645] [eta4056_charger.c] chgen_protect_cfg_init():open /etc_ro/charger_protect.cfg ERROR!!! [ 10.075836] i2c-core: driver [zx234502-charger] using legacy suspend method [ 10.076904] i2c-core: driver [zx234502-charger] using legacy resume method [ 10.079010] cpuidle: using governor ladder [ 10.080566] mmc,ZX29 Multimedia Card Interface Driver [ 10.081604] dw_mci_pltfm_register: host0 step 1 finish, reg addr f8610000 [ 10.082733] zx29_sd zx29_sd.0: Using internal DMA controller. [ 10.083770] zx29_sd zx29_sd.0: FIFO Threshold 0x1FF0000 [ 10.084747] zx29_sd zx29_sd.0: Version ID 210a [ 10.086364] mmc,dw_mci_strengthen_driver, 3841: clkcmd:0x38383858 data:0x38583838 [ 10.086364] [ 10.088165] mmc,dw_mci_strengthen_driver, 3854: clkcmd:0x3939395a data:0x38583939 [ 10.088165] [ 10.089508] zx29_sd zx29_sd.0: DW MMC controller at irq 48, 32 bit host data width, 128 deep fifo [ 10.093902] zx29_sd zx29_sd.0: Using internal DMA controller. [ 10.095092] zx29_sd zx29_sd.0: 1 slots initialized [ 10.096008] dw_mci_pltfm_register: host1 step 1 finish, reg addr f8611000 [ 10.097106] zx29_sd zx29_sd.1: Using internal DMA controller. [ 10.098632] zx29_sd zx29_sd.1: FIFO Threshold 0x3FF0000 [ 10.099578] zx29_sd zx29_sd.1: Version ID 210a [ 10.100708] mmc,dw_mci_strengthen_driver, 3858: clkcmd:0x38583939 data:0x38383838 [ 10.100708] [ 10.102447] mmc,dw_mci_strengthen_driver, 3866: clkcmd:0x395b3939 data:0x39393939 [ 10.102447] [ 10.104339] zx29_sd zx29_sd.1: DW MMC controller at irq 45, 32 bit host data width, 128 deep fifo [ 10.107269] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125) [ 10.110412] zx29_sd zx29_sd.1: 1 slots initialized [ 10.120056] [zram_init][783] ZCompress[c0107237] ZDecompress[c010743d] [ 10.133056] [xxx] efuse dev inited! [ 10.133850] [check privateip]zte_check_privateip_module_init register start... [ 10.134948] GACT probability NOT on [ 10.135711] Failed to load ipt action [ 10.139709] netem: version 1.3 [ 10.139923] u32 classifier [ 10.140625] Performance counters on [ 10.141448] input device check on [ 10.142425] Actions configured [ 10.142700] Netfilter messages via NETLINK v0.30. [ 10.143707] nfnl_acct: registering with nfnetlink. [ 10.144317] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 50000000Hz, actual 50000000HZ div = 1) [ 10.146270] mmc0: new high speed SDIO card at address 0001 [ 10.150054] nf_conntrack version 0.5.0 (368 buckets, 4832 max) [ 10.151336] ctnetlink v0.93: registering with nfnetlink. [ 10.154205] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.155761] TCP: cubic registered [ 10.156005] NET: Registered protocol family 10 [ 10.157928] rtw_drv_init: sdio_func_id is "mmc0:0001:1" [ 10.158782] =====>>INSIDE rtl8192cd_init_one <<===== [ 10.164459] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 10.165649] IPv6 over IPv4 tunneling driver [ 10.185424] NET: Registered protocol family 17 [ 10.186248] Bridge firewalling registered [ 10.187011] Ebtables v2.0 registered [ 10.188018] 8021q: 802.1Q VLAN Support v1.8 [ 10.189239] [DEBUG] create sysfs interface OK. [ 10.190032] [DEBUG] create test sysfs interface OK. [ 10.190948] [DEBUG] create test clk sysfs interface OK. [ 10.201812] NET_WAN :0 [ 10.205596] register_netdev error:0 :0 [ 10.206268] NET_WAN :1 [ 10.210449] register_netdev error:0 :1 [ 10.211120] NET_WAN :2 [ 10.215301] register_netdev error:0 :2 [ 10.215972] NET_WAN :3 [ 10.220733] register_netdev error:0 :3 [ 10.221069] NET_WAN :4 [ 10.256866] chg type PC [ 10.257995] register_netdev error:0 :4 [ 10.258209] dwc_otg_usb_chg_detect, g_plug_in:1, type:pc [ 10.258972] NET_WAN :5 [ 10.260040] ***Power on by USB*** [ 10.262817] register_netdev error:0 :5 [ 10.263153] NET_WAN :6 [ 10.265594] register_netdev error:0 :6 [ 10.265899] NET_WAN :7 [ 10.268646] register_netdev error:0 :7 [ 10.272033] zx234290-rtc zx234290-rtc: setting system clock to 2000-01-01 00:00:12 UTC (946684812) [ 10.274047] [SLP] Power/PM_INIT [ 10.274261] [SLP] Power/SPM_INIT [ 10.274688] [SLP] Power/PM_CONTEXT_INIT [ 10.275177] [SLP] Power/WAKEUP_ADDRESS [ 10.275695] [SLP] alloc size: 32 Bytes , total size 32 Bytes [ 10.276367] [SLP] alloc size: 2592 Bytes , total size 2624 Bytes [ 10.277099] [SLP] alloc size: 96 Bytes , total size 2720 Bytes [ 10.278228] [SLP] alloc size: 32 Bytes , total size 2752 Bytes [ 10.279785] [SLP] alloc size: 128 Bytes , total size 2880 Bytes [ 10.280883] [SLP] alloc size: 64 Bytes , total size 2944 Bytes [ 10.282714] [SLP] alloc size: 60 Bytes , total size 3004 Bytes [ 10.283386] [SLP] alloc size: 64 Bytes , total size 3068 Bytes [ 10.284088] [SLP] alloc size: 128 Bytes , total size 3196 Bytes [ 10.284851] [SLP] alloc size: 128 Bytes , total size 3324 Bytes [ 10.285583] [SLP] alloc size: 288 Bytes , total size 3612 Bytes [ 10.286315] [SLP] alloc size: 64 Bytes , total size 3676 Bytes [ 10.287048] [SLP] alloc size: 96 Bytes , total size 3772 Bytes [ 10.288269] [SLP] alloc size: 128 Bytes , total size 3900 Bytes [ 10.289947] [SLP] alloc size: 64 Bytes , total size 3964 Bytes [ 10.291290] [SLP] alloc size: 352 Bytes , total size 4316 Bytes [ 10.292816] [SLP] alloc size: 64 Bytes , total size 4380 Bytes [ 10.293487] [SLP] alloc size: 32 Bytes , total size 4412 Bytes [ 10.294219] [SLP] Power/PM_CONTEXT_INIT END [ 10.294738] [SLP] Power/SRAM_INIT [ 10.295166] [SLP] create sysfs interface [ 10.295928] [CPUIDLE] zx_cpu_idle init OK [ 10.295928] , [ 10.296447] [CPUFREQ] zx29_cpufreq_init ok [ 10.296997] [CPUFREQ] zx_cpufreq_cpu_init cpu: 0, target_freq:624000 [ 10.299041] [CPUFREQ] register cpufreq driver OK! [ 10.305084] =====>>EXIT rtl8192cd_init_one <<===== [ 10.305847] =====>>INSIDE rtl8192cd_init_one <<===== [ 10.307891] =====>>EXIT rtl8192cd_init_one <<===== [ 10.308654] =====>>INSIDE rtl8192cd_init_one <<===== [ 10.309722] =====>>EXIT rtl8192cd_init_one <<===== [ 10.310211] =====>>INSIDE rtl8192cd_init_one <<===== [ 10.310943] =====>>EXIT rtl8192cd_init_one <<===== [ 10.332336] zx29_sd zx29_sd.1: Using internal DMA controller. [ 10.347290] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 10.368774] mmc1: host doesn't support card's voltages [ 10.369232] mmc1: error -22 whilst initialising SDIO card [ 10.373901] mmc1: host doesn't support card's voltages [ 10.374359] mmc1: error -22 whilst initialising MMC card [ 10.376068] zx29_sd zx29_sd.1: Using internal DMA controller. [ 10.387268] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84) [ 10.409973] mmc1: host doesn't support card's voltages [ 10.410430] mmc1: error -22 whilst initialising SDIO card [ 10.416412] mmc1: host doesn't support card's voltages [ 10.416870] mmc1: error -22 whilst initialising MMC card [ 10.418579] zx29_sd zx29_sd.1: Using internal DMA controller. [ 10.432312] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 200000Hz, actual 200000HZ div = 125) [ 10.457275] mmc1: host doesn't support card's voltages [ 10.457763] mmc1: error -22 whilst initialising SDIO card [ 10.466308] mmc1: host doesn't support card's voltages [ 10.466796] mmc1: error -22 whilst initialising MMC card [ 10.468475] zx29_sd zx29_sd.1: Using internal DMA controller. [ 10.482330] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250) [ 10.517364] mmc1: host doesn't support card's voltages [ 10.517822] mmc1: error -22 whilst initialising SDIO card [ 11.077575] [eta4056_charger.c] chgen_protect_cfg_init():open /etc_ro/charger_protect.cfg ERROR!!! [ 11.818420] VFS: Mounted root (jffs2 filesystem) readonly on device 31:5. [ 11.819274] Freeing init memory: 84K [ 11.819549] Write protecting the kernel text section c0048000 - c03d0000 Starting mdevd... [ 12.792602] jffs2: Empty flash at 0x005d01e8 ends at 0x005d0800 fs_check mount_fs_partition begin [ 13.663116] jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x022d9fdc: Read 0xffffffff, calculated 0xbf642ba9 fs_check mount userdata succsee! fs_check mount_fs_partition begin [ 14.107910] jffs2: Empty flash at 0x00015ad8 ends at 0x00016000 fs_check mount nvrofs succsee! [ 16.189849] cpko: module_layout: kernel tainted. [ 16.190246] Disabling lock debugging due to kernel taint [ 16.190917] cpko: module license 'Proprietary' taints kernel. [ 16.221496] vmalloc: allocation failure: 0 bytes [ 16.221893] insmod: page allocation failure: order:0, mode:0xd0 Setting up swapspace version 1, size = 12578816 bytes [ 16.476104] Ramdump server init success! [ 16.581085] Adding 12284k swap on /dev/zram0. Priority:-1 extents:1 across:12284k SS get_update_status, read_update_status from /cache/zte_fota/update_status update_status=6 [sdcard][657]: fread /sys/devices/platform/zx29_hsotg.0/gadget/lun0/cdrom error. [sdcard][657]: fread /sys/devices/platform/zx29_hsotg.0/gadget/lun1/cdrom error. [sdcard][657]: sd_hotplug:cdrom=1 [sdcard][657]: sd_hotplug usb_lun_path=/sys/devices/platform/zx29_hsotg.0/gadget/lun1/file [net][664]: zte_mainctrl begin ======= build date: Sep 8 2023 16:31:03 [at][662]: <====== AT_CTL start ======> [at][662]: AT_CTL build date===>Sep 8 2023,16:31:00 [at][662]: i[ 16.597991] [zx snit openoft wdt]: g_wdt_nv_priority=0 invalid! [ 16.600860] [zx soft wdt]: zx_wdt_init Success!!! [ 16.600860] [t ttyS0 => fd: -1 er_no: 2 sc] <6>[TSC] create sysfs interface [ 16.600982] [tsc] g_adc1_flag:0, g_adc2_flag:1. [ 16.600982] [tsc] TsNvData.DetectEn != 0xB2. [ 16.601013] ZTEMainThread used greatest stack fota_dm[673]: [FOTA_DM][NORMAL][fota_dm_main-1141] build date: Sep 8 2023 16:31:05 depth: 1920 bytes left [ 17.235137] gs_open, port->open_count:0 [ 17.245788] gs_open init_timer entry. [ 17.246093] gs_open init_timer exit. [at][662]: init open ttyGS0 => fd: 12 er_no: 1 [net][675]: zte_security_log begin --build date: Sep 8 2023 16:31:03 [mmi][674]: ZTE_WDT ######START###### [at][662]: at_port_state_proc new_open /dev/ttyGS0 fd=12 index=0 fota_dm[673]: [FOTA_DM][NORMAL][sig_init-722] tid:3066664144 [mmi][674]: mmi_temp_voltage_line = 967+1208+1692+1735 [mmi][67[ 17.41134]: g_mmi_temp = 4 967 1208 1692 1735 76] gs_open, port->open_count:0 [ 17.413513] gs_o[wifi][672]: [wlan][wlan_main-1242]: wlan-server start, build time:[Sep 8 2023 16:31:06] [wifi][672]: [wlan][sig_init-1143]: tid:3066795216 [mmi][674]: ZTE_WDT watchdog_app = 0 [mmi][674]: ZTE_WDT start wdt_creatMsgThread [sdcard][667]: fread pen/sys/dwc init_timer entry. [ 17.416961] gs_open init_timer exit. _usb/usbconfig/usbPlug error. [at][662]: init open ttyGS1 => fd: 14 er_no: 1 [misc][670]: [SNTP]data begin to rcv msg from queue 360459. decrypt psk1 w_code=19614939, s_aes=8644C252E3A2E80390BF7E139300951966E94BD4EF8A2C3B884CFA59CA342B2E66E94BD4EF8A2C3B884CFA59CA342B2E66E94BD4EF8A2C3B884CFA59CA342B2E [fluxstat][669]: Create_Data_Thread_result SUCCESS! [fluxstat][669]: data begin to rcv msg from queue 262152. decrypt psk2 w_code=19614939, s_aes=8644C252E3A2E80390BF7E139300951966E94BD4EF8A2C3B884CFA59CA342B2E66E94BD4EF8A2C3B884CFA59CA342B2E66E94BD4EF8A2C3B884CFA59CA342B2E [wifi][672]: [wlan][send_get_mac_req-600]: wifi_ssid_init: ssid_write_flag = 1 [at][662]: at_port_state_proc new_open /dev/ttyGS1 fd=14 index=1 [SMS] ======/etc_rw/sms.db exist. [wifi][672]: [wlan][get_mac_config_ssid_key_nv-622]: wifi_ssid_init: ssid_write_flag = 1 net.unix.max_dgram_qlen = 5000 chmod: /etc/shadow: Read-only file system sh: 1: unknown operand Starting FOTA apps......!! date: invalid date '%H:%M:%S' [usbcfgmng][667]: [usbCfgMng]usbcfg_browse_cdrom error [mmi][685]: ZTE_WDT BOOT_TESTBATTERY_MODE= [zcat] zcat_mode = 0xc5 [zcat] zcat_usblog = ttyGS2 [ 17.949249] cplog open. [zcat] init logdev success. [zcat] init peripheral success. fota_dm[673]: [FOTA_DM][NORMAL][fota_dm_main-1171] auto polling on fota_dm[673]: [FOTA_DM][NORMAL][fota_dm_main-1172] poweron auto check on fota_dm[673]: [FOTA_DM][NORMAL][fota_dm_add_rtc_alarm-682] ret=0, time interval=300 fota_dm[673]: [FOTA_DM][NORMAL][fota_dm_main-1179] start rtc alarm [rtc][663]: rtc-service: process_msg RTC_MSG_ADD_ALARM, src:0x1013, g_clean_flag = 0. [rtc][663]: rtc-service: handle_alarm_add pAlarm->interval is 300 ,pAlarm->time_val() is 946684820, is_utc:0. [rtc][663]: rtc-service: alarm_restart: set timer ok, remain_time:300, cur_rtc_time:946684820, module:0x1013, rtc_id:0x0 [rtc][663]: rtc-service: msg_looper process_msg out. [mmi][685]: ZTE_WDT BATTERY wdt_get_battery_temp_voltage temp = 1774! [usbcfgmng][667]: [usbCfgMng] do_usb_enum type = 0 [usbcfgmng][667]: [usbCfgMng] usb_enum_CdromProc cdrom tempModeType =0 [usbcfgmng][667]: [usbCfgMng][usb_setMsLunxFilePathAndInquiryString][563]lun_id = 0, msType = 0, lun_path = /mnt/resource/ufi_cdrom.iso, filepath = /sys/devices/platform/zx29_hsotg.0/gadget/lun0/file InitGUI begin!