Siddharth Vadapalli <s-vadapalli@ti.com> says:
Hello,
This series adds support for the Cadence PCIe controller on TI's K3
family of SoCs to which the J7200 SoC belongs. The driver is an adaptation
of the Linux driver (drivers/pci/controller/cadence/pci-j721e.c) and has
been implemented specifically for Root-Complex mode of operation on the
J7200 SoC. A minor set of changes will be sufficient to support other K3
SoCs as well with plans to implement it in the near future.
Link: https://lore.kernel.org/r/20241014053924.4027491-1-s-vadapalli@ti.com
Add support for the Cadence PCIe Controller present on TI's K3 SoCs.
This driver is an adaptation of the Linux driver.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Provide a short description of how tests work, why they are so critical
and how to resolve gaps in Binman's test coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Add new section for USB TypeC Port Manager (TCPM) support, which
is needed to figure out cable orientation of USB-C plus and to do
USB PD communication.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Marek Vasut <marex@denx.de>
Add myself as a maintainer for the lwIP network stack integration code
and network commands as well as the sandbox ethernet driver for lwIP.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Oliver Gaskell <Oliver.Gaskell@analog.com> says:
ADSP-SC5xx is a series of ARM-based DSPs.
This comprises the armv7 based SC57x, SC58x and SC594 series, and the
armv8 based SC598.
This patch series includes configurations, init code, and minimal DTs
to enable Analog Devices' evaluation boards for these SoCs to boot
through SPL and into U-Boot Proper, as well as devicetree schemas for
the added DTs.
This patch series depends on ("arm: Add Analog Devices SC5xx Machine
Type") (https://lists.denx.de/pipermail/u-boot/2024-April/552043.html)
Adds minimal device tree for Analog Devices' SC573-EZKIT board and
common files for the SC57x/SC5xx family.
This also adds all sc5* devicetrees to ARM SC5XX in MAINTAINERS, and
adds the ADSP Linux mailing list as the list for ARM SC5XX.
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Introduce a defconfig for the RB3 Gen 2 and other QCM6490 boards with a
dedicated uefi partition. These can replace EDK2 entirely with U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Now that sandbox_vpl supports UPL, add a test that checks that the
payload can be loaded by SPL and the handoff information passed through
to U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the basic code to create a handoff structure in SPL, so it can be
passed to the next phase. For now this is not plumbed in.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a 'upl' command to work with Universal Payload features. For now it
only supports reading and writing a handoff structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Universal Payload provides a standard way of handing off control between
two firmware phases. Add support for reading the handoff information into
a structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Pinctrl drivers were moved to a dedicated directory but the entry was never
updated, so add the pinctrl-ipq4019 driver entry.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The reset handling was added to the clock drivers but the entry was never
updated, so add the clock-ipq4019 driver instead.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The separate clock and reset dt-bindings for IPQ40XX were merged into one
recently, but the entry was not updated so do it now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
ArmSoM Sige7 is a Rockchip RK3588 based SBC (Single Board Computer) by
ArmSoM.
There are two variants depending on the DRAM size : 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB memory LPDDR4x
Mali G610MC4 GPU
2x MIPI CSI 2 multiple lanes connector
64GB/128GB on board eMMC
uSD slot
1x USB 2.0 Type-A, 1x USB 3.0 Type-A, 1x USB 3.0 Type-C
1x HDMI 2.1 output
2x 2.5 Gbps Ethernet port
40-pin IO header including UART, SPI and I2C
USB PD over USB Type-C
Size: 92mm x 62mm
Kernel commit:
81c828a67c78 (arm64: dts: rockchip: Add ArmSom Sige7 board)
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use upstream device tree files and bindings. To do so:
- imply (enable) OF_UPSTREAM option for E850-96 target
- point DEFAULT_DEVICE_TREE in E850-96 config to upstream dts
- remove now not needed local dts files, binding docs and headers
- update MAINTAINERS and board/samsung/e850-96/MAINTAINERS
correspondingly
Upstream device tree files for Exynos850 SoC and E850-96 board are
pretty much the same as local (removed) ones, so the conversion is
rather straightforward and painless in this case. The appended dts file
(arch/arm/dts/exynos850-e850-96-u-boot.dtsi) stays unchanged.
The only remaining local dt-bindings doc for E850-96 board is
exynos-pmu.yaml. It wasn't removed as it's quite different from Linux
kernel version. Particularly U-Boot local version of exynos-pmu.yaml
describes "samsung,uart-debug-1" property, which is not present in Linux
kernel binding. Later it might be upstreamed to Linux kernel, and once
it's done the U-Boot exynos-pmu.yaml binding can be removed.
No functional change.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Sughosh Ganu <sughosh.ganu@linaro.org> says:
The following patch series adds support for version 2 of the FWU
metadata. The version 2 metadata structure is defined in the latest
revision of the FWU specification [1].
The earlier versions of these patches were migrating to a version 2
only support in U-Boot, similar to TF-A. However, based on feedback
from ST [2], this series has been updated to support both versions. A
platform would still be needed to enable one of the two versions of
metadata through a config symbol.
TF-A has code which reads the FWU metadata and boots the platform from
the active partition. TF-A has decided to migrate the FWU code to a
version 2 only support. These changes have been merged in upstream
TF-A.
These changes have been tested on the ST DK2 board, which uses the GPT
based partitioning scheme. Both V1 and V2 metadata versions have been
tested on the DK2 board.
These changes need to be tested on platforms with MTD partitioned
storage devices.
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Greg Malysa <greg.malysa@timesys.com> says:
This series adds support for the ADI SC5xx machine type and includes two
core drivers that are required for being able to boot any board--a UART
driver, the gptimer driver which is used as a clock reference (CNTVCNT
is not supported on the armv7 sc5xx SoCs) and the clock tree driver. Our
corresponding Linux support relies on u-boot configuring the clocks
correctly before booting, so it is not possible to boot any board
without the CGU/CDU configuration happening here. There are also no
board files, device trees, or defconfigs included here, but some common
definitions that will be used to build board files currently are. The
sc5xx SoCs themselves include many armv7 families (sc57x, sc58x, and
sc594) all using an ARM Cortex-A5, and one armv8 family (sc598) indended
to be a drop-in replacement for the SC594 in terms of peripherals, with
a Cortex-A55 instead.
Some of the configuration code in dmcinit and clkinit is quite scary and
causes a lot of checkpatch violations. It is modified from code
initially provided by ADI, but it has not been fully rewritten. There's
a question of how important it is to clean up this code--it has some
quality violations, but it has been in use (including in production) for
over two years and is known to work for performing the low level SoC
initialization, while a rewrite might introduce timing or sequence bugs
that could take a significant amount of time to detect in the future.
Add support for the SC5xx machine type from Analog Devices. This
includes support for the SC57x, SC58x, SC59x, and SC59x-64 SoCs, which
have many common features such as common ADI IP blocks, and SHARC DSP
cores. This commit introduces core functionality required for all boards
using an SC5xx SoC, such as:
- SPL configuration
- Required CPU hooks such as reset
- Boot ROM interaction to load the stage 2 bootloader in the reference
configuration. Other options are possible but not officially supported
at this time
- SoC-common configuration expected to be reused by all boards
- Early initialization for system clocks and DDR controller
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Joel is no longer with Broadcom. Remove his email from bcmbca maintainer
list and replace him with myself for stack protection maintainer.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Add orphaned TEE/OP-TEE-related files to TEE subsystem entry in
MAINTAINERS. This includes:
- optee_rpmb cmd and test for it
- Misc. OP-TEE tests
- OP-TEE SCMI agent implementation
- Documentation, including device tree bindings
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
