While I had thought this commit was a cherry-pick from upstream, it is
not. And so, this is not allowed here.
This reverts commit dfe5f16a33.
Signed-off-by: Tom Rini <trini@konsulko.com>
(cherry picked from commit 6ceb861882)
Now that pre-relocation devicetree mnipulation uses an event rather than
a weak function, update the docs and remove the function from the init.h
header.
Series-to: u-boot
Cover-letter:
fdt: Use events for pre-relocation devicetree manipulation
At present a weak function is used to modify the devicetree before
relocation. This is not ideal, since it is hard to find out whether a
board provides this function or not.
Another issue is that the fixups happen in multiple places in the init
sequences, with a confusing set of #if checks.
A final issue is that the fixups are done on the flat tree, which can be
quite inefficient.
This series introduces a new event to handle these fixups, converts all
boards and update the docs. The event passes an oftree instead of a
void * so that in future it can support livetree updates.
It would be possible to remove OF_BOARD_FIXUP and just always send the
event, but this would have a small code-size impact on the majority of
boards, since only about 45 use this feature.
END
Rather than using a weak function for pre-relocation devicetree-fixups,
use the new EVT_FT_FIXUP_F event.
Mark the functions as static and make a few other minor tweaks to tidy
up the code.
The existing logic for handling receiving a devicetree from a previous
phase is quite complicated. Simplify it in preparation for introducing
standard passage.
Add a Kconfig called OF_PASSAGE which indicates that the devicetree
must come from standard passage.
Series-changes: 3
- Add new patch to redo how a devicetree is set up
Series-changes: 4
- Drop now-unused label
Series-changes: 5
- Use OF_PASSAGE here instead of OF_BLOBLIST
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is impossible to change the qemu_arm64 defconfig to
obtain a devicetree from the U-Boot build.
This is necessary for FIT validation, for example, where the signature
node must be compiled into U-Boot.
A proposed change to QEMU to allow device tree additions has been
blocked for several years. The only known workaround is to use QEMU's
dumpdtb option, merge in the signature node manually, disable
OF_HAS_PRIOR_STAGE and then start QEMU with special arguments. This is
complicated enough that it is documented in U-Boot[1].
Unfortunately the only way to disable OF_HAS_PRIOR_STAGE at present is
to hack the Kconfig.
Add a new QEMU_MANUAL_DTB Kconfig option which makes OF_HAS_PRIOR_STAGE
optional, thus avoiding needing to patch U-Boot to get this working.
This seems a clearer solution than just making OF_HAS_PRIOR_STAGE
visible, since that symbol is intended to be set automatically by each
platform.
Series-to: u-boot
Series-cc: trini
Series-cc: Peter Maydell <peter.maydell@linaro.org>
Series-cc: Andrew Phelps <andrew.phelps@canonical.com>
Series-cc: ilias
Series-changes: 2
- Add a new QEMU-specific Kconfig instead
- Move patch into the standard-passage series
Series-changes: 3
- Fix 'usiing' typo
- Add mention of QEMU_MANUAL_DTB in doc/
[1] https://docs.u-boot.org/en/latest/develop/devicetree/dt_qemu.html
Link: https://patchwork.kernel.org/project/qemu-devel/patch/20210926183410.256484-1-sjg@chromium.org/#24481799
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
As the name implies, it is built around the RK3576 SoC with 4x Cortex-A72
cores, four Cortex-A53 cores and Mali-G52 MC3 GPU.
Storage options are EMMC, SD-Card, a 2242 M.2 slot and the possibility to
use UFS 2.0 storage.
Video Output options are a HDMI port, a DSI connector as well as Display-
Port via the TypeC connector (all of them not yet supported).
Networking options are a Low-profile Gigabit Ethernet RJ45 port with
Motorcomm YT8531 PHY as well as WiFi via an AMPAK AP6256 module.
USB ports on the board are 1x USB 3.0 port, 1x USB 2.0 port, 1x USB Type-C
and it comes with 40-pin GPIO header
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250210205126.1173631-3-heiko@sntech.de
[ upstream commit: 887ff17cdd8f088a52e2b61e71f2b6c9b9678de6 ]
(cherry picked from commit 388e7272d092bd20e414cd408bac39d8fd02d765)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa E20C has two buttons, one SARADC maskrom button and one GPIO user
button.
Add support for the maskrom button using a adc-keys node, also add the
regulators used by SARADC controller.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250304201642.831218-5-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 3a2819ee9c71d1c6388e456cc4eb042914d15d7e ]
(cherry picked from commit 460ef5b623e5fa69843305faf50f6b1a8e81e1cd)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa E20C has three gpio controlled leds (sys, wan and lan).
Add led nodes and set default trigger to heartbeat for the sys led and
netdev for the lan and wan leds.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250304201642.831218-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 6a709e003492e9878d5f1357be0b2e1162e1e6a6 ]
(cherry picked from commit a3556ede6b48c7760ac3608ad77601fca26d2ce0)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa E20C route UART0 M0 pins (GPIO4_C7 and GPIO4_D0) to the onboard
CH340B for debug console use.
Add pinctrl for UART0 M0 pins used for serial console.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250228064024.3200000-6-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 0d2312f0d3e4ce74af0977c1519a07dfc71a82ac ]
(cherry picked from commit 9bcf6ccdd87c3be48fe7d75150c6e403c5c0a42d)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Quality-of-Service (QsS) node stores/restores specific
register contents when the power domains is turned off/on.
Add QoS node so that they can connect to the power domain.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20250306123809.273655-3-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 61a05d8ca3030a544175671f5fab7a8f29c24085 ]
(cherry picked from commit 9ee90dfd6957fcc42ea94c43d195b01d1b286713)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add pinctrl and gpio nodes for RK3528 and import rk3528-pinctrl.dtsi
from vendor linux-6.1-stan-rkr5 kernel with the hdmi-pins-idle node
removed due to missing label reference to pcfg_output_low_pull_down.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250228064024.3200000-5-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: a31fad19ae39ea27b5068e3b02bcbf30a905339b ]
(cherry picked from commit 89a24fa2e923b68a42ccc8cc9cb2d5bdf291ac40)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dt node for RK3528 clock and reset unit. Clock "gmac0_clk" is
generated by internal Ethernet phy, a fixed clock node is added as a
placeholder to avoid orphans.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Link: https://lore.kernel.org/r/20250217061142.38480-9-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 858cdcdd11cf9913756297d3869e4de0f01329ea ]
(cherry picked from commit 60741472b42e92d2393327cb70669ab90e3b382f)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are two types of clocks in RK3528 SoC, CRU-managed and
SCMI-managed. Independent IDs are assigned to them.
For the reset part, differing from previous Rockchip SoCs and
downstream bindings which embeds register offsets into the IDs, gapless
numbers starting from zero are used.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250217061142.38480-6-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: e0c0a97bc308f71b0934e3637ac545ce65195df0 ]
(cherry picked from commit 8768d063e732e64892e4d1d09aa583d1394c8388)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BootROM leave GPIO4_D6 configured as SDMMC_PWREN function and DW MCI
driver set PRWEN high on MMC_POWER_UP and low on MMC_POWER_OFF.
Similarly U-Boot also set PRWEN high before accessing mmc.
However, HW revision prior to v1.2 must pull GPIO4_D6 low to access
sdmmc. For HW revision v1.2 the state of GPIO4_D6 has no impact.
Model an always-on active low fixed regulator using GPIO4_D6 to fix
use of sdmmc on older HW revisions of the board.
Fixes: adeb5d2a4ba4 ("arm64: dts: rockchip: Add Radxa ROCK S0")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20241119230838.4137130-1-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 26c100232b09ced0857306ac9831a4fa9c9aa231 ]
(cherry picked from commit ca8e0bedbc790b19b11efc223677d178b8eeb74e)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
QEMU always gets its devicetree from the OF_BOARD mechanism so we should
not depend on !BLOBLIST here.
It's not clear why we need to have any relationship with BLOBLIST so
let's remove the entire condition.
The logic of PRIOR_STAGE is quite a mess, unfortuantely. We should rely
only standard passage to receive things from the prior stage. QEMU
should implement standard passage to provide its devicetree to U-Boot
However Linaro has blocked my patch to provide devicetree additions[1],
so little breath should be held in respect of either change.
[1] https://lore.kernel.org/qemu-devel/20210926183410.256484-1-sjg@chromium.org/
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 2b71470628 dts: OF_HAS_PRIOR_STAGE should depend on !BLOBLIST
Reviewed-by: Tom Rini <trini@konsulko.com>
Radxa ROCK 5C is a 8K computer for everything[1] using the Rockchip
RK3588S2 chip:
- Rockchip RK3588S2
- Quad A76 and Quad A55 CPU
- 6 TOPS NPU
- up to 32GB LPDDR4x RAM
- eMMC / SPI flash connector
- Micro SD Card slot
- Gigabit ethernet port (supports PoE with add-on PoE HAT)
- WiFi6 / BT5.4
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST port
- 1x USB Type-C 5V power port
[1] https://radxa.com/products/rock5/5c
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20241021090548.1052-2-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 3ddf5cdb77e6efd6fe9b70f36dec935e324a3cd2 ]
(cherry picked from commit f80689fcef4b9b07a97b629b4075cc1a4c21a68e)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These pinctrls manage the low-speed PCIe signals:
- CLKREQ#: An output on the RK3588 (both RC or EP modes), used to
request that external clock-generation circuitry provide a clock.
- PERST#: An input on the RK3588 in EP mode, used to detect a reset
signal from the RC. In RC mode, the hardware does not use this signal:
Linux itself generates it by putting the pin in GPIO mode.
- WAKE#: In EP mode, this is an output; in RC mode, this is an input.
Each of these signals serves a distinct purpose, and more importantly,
PERST# should not be muxed when the RK3588 is in the RC role. Bundling
them together in pinctrl groups prevents proper use: indeed, almost none
of the current board-specific .dts files make any use of them.
(Exception: Rock 5A recently had a patch land that misuses _pins; this
patch corrects that.)
However, on some RK3588 boards, the PCIe 3 controller will indefinitely
stall the boot if CLKREQ# is not muxed (details in the next patch).
This patch unbundles the signals to allow them to be used.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Link: https://lore.kernel.org/r/20240912025034.180233-2-CFSworks@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 4294e32111781b3de4d73b944cbd1bc1662a9a7a ]
(cherry picked from commit 8713425fa162b61bcf5f7a6dcd171fddfb12be36)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Typically any non-removable storage (emmc) is listed before removable
storage (sd-card) options. Also U-Boot will try to override and use
mmc0=sdhci and mmc1=sdmmc0 for all rk356x boards.
Fixes: 50decd493c83 ("arm64: dts: rockchip: Add FriendlyARM NanoPi R3S board")
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Link: https://lore.kernel.org/r/20241022193537.1117919-6-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: b7cd1115456d312f8c5e60c80fdc35fd35ea6eab ]
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The R2S Plus is basically an R2S with additional eMMC.
The eMMC configuration for the DTS has been extracted and copied from
rk3328-nanopi-r2.dts, v2017.09 branch from the friendlyarm/uboot-rockchip
repository.
Signed-off-by: Sergey Bostandzhyan <jin@mediatomb.cc>
Link: https://lore.kernel.org/r/20240814170048.23816-2-jin@mediatomb.cc
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: b8c02878292200ebb5b4a8cfc9dbf227327908bd ]
(cherry picked from commit c9bf98827964441f4dd16faa45bd4046f472e693)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cool Pi CM5 GenBook works as a carrier board connect with CM5 [0].
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
This patch add basic support to bringup eMMC/USB HOST/WiFi/TouchPad/
Battery/PCIE NVME, and can also drive a HDMI output with out of tree
hdmi patches.
[0] https://www.crowdsupply.com/shenzhen-tianmao-technology-co-ltd/genbook-rk3588
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20240730102433.540260-3-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 4a8c1161b843c366776fc872a6fe45b743b2983e ]
(cherry picked from commit dc6316da23734d9321e09f8c8a7669f4b4cb9f75)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the DH electronics i.MX6DL DHCOM SoM and a PDK2 evaluation
board. The evaluation board features three serial ports, USB OTG, USB host
with an USB hub, Fast or Gigabit ethernet, eMMC, uSD, SD, analog audio,
PCIe and HDMI video output.
All of the aforementioned features except for mSATA are supported, mSATA
is not available on i.MX6DL and is only available on DHCOM populated with
i.MX6Q SoC which is already supported upstream.
Backport from linux-next commit
c3f5d76a6e03 ("ARM: dts: imx6dl: Add support for i.MX6DL DHCOM SoM on PDK2 carrier board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The device contains two i2c-connected eeproms holding some product-
specific values. One sitting on the mainboard and one on the statically
connected backplane.
While the eeprom chips themself have a size of 512 byte, the eeprom data
only uses 256 byte each, probably to stay compatible with other models.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240810211438.286441-3-heiko@sntech.de
[ upstream commit: da6f4130234448122fe3e66c8116f7d9eea8a5c7 ]
(cherry picked from commit 0b3109708caf5002ba188ae28eae9ce46b2c39b4)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Contrary to the vendor-kernel the pmu-io-domains are not enabled by
default. This resulted in the value not being set according to the
regulator, which in turn made the gmac0 interface that is connected
to the vccio4 supply inoperable.
Fixes: 64b7f16fb394 ("arm64: dts: rockchip: add 2 pmu_io_domain supplies for Qnap-TS433")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240805162052.3345768-1-heiko@sntech.de
[ upstream commit: 40cc4257169712f0ae3835820a4c5afbdd1a16ff ]
(cherry picked from commit f509fcb1fb82117e551b489592ac5714a6c5cd8d)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
While it requires to have the right phy driver loaded (i.e. motorcomm)
to make the phy asserting the right delays, this is generally the
preferred way to define the MAC <-> PHY connection.
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240304084612.711678-2-ukleinek@debian.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: e8d45544f806f3b55c30345de84262cbb9504902 ]
(cherry picked from commit e0bbe061fd537bd7b113c53eb046bbcbf0e6597d)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The TS433 doesn't provide display output, but the gpu nevertheless can be
used for compute tasks for example.
So there is no reason not to enable it.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-14-heiko@sntech.de
[ upstream commit: 9130eb62586f4cef0557d0378fb7e78d7397ab2d ]
(cherry picked from commit e324a9e8ea083ebdca207b5ca2ed86d2b5f862a0)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fill in the missing pieces for RK809 pmic used on the TS433.
The regulator setup comes from the vendor-devicetree, so without proper
schematics its accuracy is somewhat unclear, but it looks really similar
to all the other rk3568 boards, so follows the reference design it seems.
The one caveat is related to vcc3v3_sd. This regulator needs to stay on.
When turned off because of no users, access to both PCIe controllers
will stall. Maybe this rail does supply the 100MHz refclk generation
or so.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-13-heiko@sntech.de
[ upstream commit: ee078c7daa98353496410b715a5acbb41d7d3a90 ]
(cherry picked from commit 48951cb085998a5c8e3650351a794b136dac648f)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The TS433 seems to use a silergy,syr827 regulator for the cpu supply.
At least that is the compatible used in the vendor devicetree, though
it could very well also be another fan53555 clone.
Define the needed regulator node and hook up the cpu-supply to the
cpu cores.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-12-heiko@sntech.de
[ upstream commit: 99b36ba910d896bddbb9a190ca686c6d9cd0325f ]
(cherry picked from commit 2f0afd1a3cbf6f3192dc7a5c496affab718671b3)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The TS433 has 3 buttons, power and copy in the front as well as a reset
pinhole button on the back. The power-button is connected to the embedded
controller while the other two buttons are just gpio connected.
Add the gpio-keys definition for the two buttons we can handle right now.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-11-heiko@sntech.de
[ upstream commit: 9b682d31b24f1f70b5b4d0618095d46e0722b9d8 ]
(cherry picked from commit f0b858c751382ee9faf18f9b19b0817c6b50ac1c)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
